| ELECTRICAL ERROR ANGULAR RANGE IN MINUTES | -7.0 TO 7.0 |
| ACTUATOR FRICTION TORQUE AT MINUS 55 DEG CELSIUS | 0.07 INCH-OUNCES MAXIMUM |
| ACTUATOR FRICTION TORQUE AT PLUS 25 DEG CELSIUS | 0.07 INCH-OUNCES MAXIMUM |
| ALIGNMENT HOLE BOLT CIRCLE DIAMETER | 0.6250 INCHES NOMINAL |
| ALIGNMENT HOLE DEPTH | 0.1250 INCHES NOMINAL |
| BODY MATERIAL | STEEL CORROSION RESISTING |
| BODY SIZE | 11 |
| BODY STYLE | STANDARD ROUND C |
| FLANGE DIAMETER | 1.0570 INCHES MINIMUM AND 1.0620 INCHES MAXIMUM |
| FLANGE THICKNESS | 0.0930 INCHES NOMINAL |
| FRAGILITY FACTOR | MODERATELY RUGGED |
| FREQUENCY IN HERTZ | 400.0 NOMINAL |
| OVERALL LENGTH | 2.3360 INCHES MINIMUM AND 2.3760 INCHES MAXIMUM |
| MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | 45.00 OUTPUT |
| MAXIMUM TEMP RISE | 20.0 CELSIUS |
| MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 75.00 |
| MOUNTING FACILITY NOMINAL SCREW THREAD DIAMETER | 0.112 INCHES |
| MOUNTING FACILITY SCREW THREAD SERIES DESIGNATOR | UNC |
| MOUNTING SURFACE TO TERMINAL END DISTANCE | 1.7910 INCHES MINIMUM AND 1.8110 INCHES MAXIMUM |
| PILOT DIAMETER | 0.6245 INCHES MINIMUM AND 0.6250 INCHES MAXIMUM |
| PILOT LENGTH | 0.0450 INCHES MINIMUM AND 0.0650 INCHES MAXIMUM |
| PHASE SHIFT ANGLE IN DEG | 4.500 INPUT TO OUTPUT NOMINAL |
| ROTOR INPUT CURRENT RATING | 31.0 MILLIAMPERES MAXIMUM |
| ROTOR INPUT ELECTRICAL POWER RATING | 490.0 MILLIWATTS NOMINAL |
| ROTOR INPUT VOLTAGE RATING IN VOLTS | 115.0 NOMINAL |
| SECURING HOLE QUANTITY | 4 |
| SHAFT DIAMETER | 0.1198 INCHES MINIMUM AND 0.1200 INCHES MAXIMUM SINGLE SHAFT |
| SHAFT SLOT DEPTH | 0.0250 INCHES NOMINAL SINGLE SHAFT |
| SHAFT SLOT WIDTH | 0.0200 INCHES NOMINAL SINGLE SHAFT |
| SHAFT TYPE | ROUND, SLOTTED SINGLE SHAFT |
| SHAFT LENGTH | 0.5460 INCHES MINIMUM AND 0.5650 INCHES MAXIMUM SINGLE SHAFT |
| SHOULDER DIAMETER | 0.9995 INCHES MINIMUM AND 1.0000 INCHES MAXIMUM |
| SHOULDER LENGTH | 0.0590 INCHES MINIMUM AND 0.0790 INCHES MAXIMUM |
| ZRO IMPEDANCE MAGNITUDE IN OHMS | 80.00 MINIMUM AND 84.00 MAXIMUM |
| ZRO RESISTANCE IN OHMS | 3720.00 MINIMUM AND 4700.00 MAXIMUM |
| ZSS IMPEDANCE MAGNITUDE IN OHMS | 17.00 MINIMUM AND 26.00 MAXIMUM |
| ZSS RESISTANCE IN OHMS | 410.00 MINIMUM AND 500.00 MAXIMUM |
| TERMINAL LOCATION | REAR |
| TERMINAL TYPE AND QUANTITY | 5 SCREW |
| TEST DATA DOCUMENT | 81349-MIL-S-20708 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| TRANSFORMATION RATIO | 0.783 ROTOR TO STATOR NOMINAL |
| UNDERCUT DIAMETER | 0.9750 INCHES NOMINAL |
| UNDERCUT WIDTH | 0.0620 INCHES NOMINAL |