| ELECTRICAL ERROR ANGULAR RANGE IN MINUTES | -6.0 TO 6.0 |
| ACTUATOR FRICTION TORQUE AT PLUS 25 DEG CELSIUS | 0.05 INCH-OUNCES MAXIMUM |
| ALIGNMENT HOLE BOLT CIRCLE DIAMETER | 1.1000 INCHES NOMINAL |
| ALIGNMENT HOLE QUANTITY | 4 |
| ALIGNMENT HOLE DEPTH | 0.1250 INCHES NOMINAL |
| BODY MATERIAL | STEEL CORROSION RESISTING |
| BODY SIZE | 15 |
| BODY STYLE | STANDARD ROUND C |
| FLANGE DIAMETER | 1.4320 INCHES MINIMUM AND 1.4370 INCHES MAXIMUM |
| FLANGE THICKNESS | 0.0930 INCHES NOMINAL |
| FREQUENCY IN HERTZ | 400.0 NOMINAL |
| OVERALL LENGTH | 2.3120 INCHES NOMINAL |
| MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | 32.00 OUTPUT |
| MAXIMUM TEMP RISE | 20.0 CELSIUS |
| MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 60.00 |
| MOUNTING SURFACE TO TERMINAL END DISTANCE | 1.7720 INCHES NOMINAL |
| PILOT DIAMETER | 0.8745 INCHES MINIMUM AND 0.8750 INCHES MAXIMUM |
| PILOT LENGTH | 0.0400 INCHES NOMINAL |
| PHASE SHIFT ANGLE IN DEG | 4.000 INPUT TO OUTPUT NOMINAL |
| ROTOR INPUT CURRENT RATING | 85.0 MILLIAMPERES MAXIMUM |
| ROTOR INPUT ELECTRICAL POWER RATING | 1.0 WATTS NOMINAL |
| ROTOR INPUT VOLTAGE RATING IN VOLTS | 115.0 NOMINAL |
| SHAFT DIAMETER | 0.1870 INCHES MINIMUM AND 0.1872 INCHES MAXIMUM SINGLE SHAFT |
| SHAFT NOMINAL THREAD SIZE | 0.190 INCHES SINGLE SHAFT |
| SHAFT THREAD CLASS | 2A SINGLE SHAFT |
| SHAFT THREAD DIRECTION | RIGHT-HAND SINGLE SHAFT |
| SHAFT THREAD LENGTH | 0.2000 INCHES NOMINAL SINGLE SHAFT |
| SHAFT THREAD SERIES DESIGNATOR | UNF SINGLE SHAFT |
| SHAFT LENGTH | 0.5400 INCHES NOMINAL SINGLE SHAFT |
| SHAFT TYPE | SPLINE W/THREADS SINGLE SHAFT |
| SHOULDER DIAMETER | 1.3115 INCHES MINIMUM AND 1.3120 INCHES MAXIMUM |
| SHOULDER LENGTH | 0.1320 INCHES NOMINAL |
| SPLINE TOOTH DIAMETRAL PITCH | 120 SINGLE SHAFT |
| SPLINE TOOTH QUANTITY | 21 SINGLE SHAFT |
| ZRO IMPEDANCE ANGLE IN DEG | 81.40 MINIMUM AND 84.60 MAXIMUM |
| ZRO IMPEDANCE MAGNITUDE IN OHMS | 1402.00 MINIMUM AND 1643.00 MAXIMUM |
| ZSS IMPEDANCE ANGLE IN DEG | 26.50 MINIMUM AND 31.50 MAXIMUM |
| ZSS IMPEDANCE MAGNITUDE IN OHMS | 123.00 MINIMUM AND 138.00 MAXIMUM |
| TERMINAL LOCATION | REAR |
| TERMINAL TYPE AND QUANTITY | 5 SCREW |
| TEST DATA DOCUMENT | 49956-362030 DRAWING (THIS IS THE BASIC GOVERNING DRAWING, SUCH AS A CONTRACTOR DRAWING, ORIGINAL EQUIPMENT MANUFACTURER DRAWING, ETC.; EXCLUDES ANY SPECIFICATION, STANDARD OR OTHER DOCUMENT THAT MAY BE REFERENCED IN A BASIC GOVERNING DRAWING) |
| TRANSFORMATION RATIO | 0.783 STATOR TO ROTOR NOMINAL |
| UNDERCUT DIAMETER | 1.3120 INCHES NOMINAL |
| UNDERCUT WIDTH | 0.0780 INCHES NOMINAL |