| ELECTRICAL ERROR ANGULAR RANGE IN MINUTES | -7.0 TO 7.0 |
| ACTUATOR FRICTION TORQUE AT PLUS 25 DEG CELSIUS | 0.07 INCH-OUNCES MAXIMUM |
| ALIGNMENT HOLE BOLT CIRCLE DIAMETER | 0.8120 INCHES NOMINAL |
| ALIGNMENT HOLE QUANTITY | 4 |
| ALIGNMENT HOLE DEPTH | 0.1250 INCHES NOMINAL |
| BODY MATERIAL | STEEL CORROSION RESISTING |
| BODY SIZE | 11 |
| BODY STYLE | STANDARD ROUND C |
| FLANGE DIAMETER | 1.0570 INCHES MINIMUM AND 1.0620 INCHES MAXIMUM |
| FLANGE THICKNESS | 0.0930 INCHES NOMINAL |
| FRAGILITY FACTOR | MODERATELY RUGGED |
| FREQUENCY IN HERTZ | 400.0 NOMINAL |
| OVERALL LENGTH | 2.4060 INCHES NOMINAL |
| MAXIMUM FUNDAMENTAL NULL VOLTAGE IN MILLIVOLTS PER VOLT | 60.00 OUTPUT |
| MAXIMUM TEMP RISE | 20.0 CELSIUS |
| MAXIMUM TOTAL NULL VOLTAGE OUTPUT IN MILLIVOLTS PER VOLT | 90.00 |
| MOUNTING SURFACE TO TERMINAL END DISTANCE | 1.8510 INCHES NOMINAL |
| PILOT DIAMETER | 0.6245 INCHES MINIMUM AND 0.6250 INCHES MAXIMUM |
| PILOT LENGTH | 0.0620 INCHES NOMINAL |
| PHASE SHIFT ANGLE IN DEG | 4.000 INPUT TO OUTPUT NOMINAL |
| SHAFT DIAMETER | 0.1872 INCHES NOMINAL SINGLE SHAFT |
| SHAFT NOMINAL THREAD SIZE | 0.190 INCHES SINGLE SHAFT |
| SHAFT THREAD CLASS | 2A SINGLE SHAFT |
| SHAFT THREAD DIRECTION | RIGHT-HAND SINGLE SHAFT |
| SHAFT THREAD LENGTH | 0.2000 INCHES NOMINAL SINGLE SHAFT |
| SHAFT THREAD SERIES DESIGNATOR | UNF SINGLE SHAFT |
| SHAFT LENGTH | 0.5550 INCHES NOMINAL SINGLE SHAFT |
| SHAFT TYPE | SPLINE W/THREADS SINGLE SHAFT |
| SHOULDER DIAMETER | 0.9995 INCHES MINIMUM AND 1.0000 INCHES MAXIMUM |
| SHOULDER LENGTH | 0.0620 INCHES NOMINAL |
| SPECIFICATION/STANDARD DATA | 81349-MIL-S-20708/81 GOVERNMENT SPECIFICATION |
| SPLINE TOOTH DIAMETRAL PITCH | 120 SINGLE SHAFT |
| SPLINE TOOTH QUANTITY | 21 SINGLE SHAFT |
| STATOR INPUT CURRENT RATING | 49.0 MILLIAMPERES MAXIMUM |
| STATOR INPUT ELECTRICAL POWER RATING | 530.0 MILLIWATTS NOMINAL |
| STATOR INPUT VOLTAGE RATING IN VOLTS | 90.0 NOMINAL |
| ZRS IMPEDANCE ANGLE IN DEG | 23.00 MINIMUM AND 33.00 MAXIMUM |
| ZRS IMPEDANCE MAGNITUDE IN OHMS | 470.00 MINIMUM AND 570.00 MAXIMUM |
| ZSO IMPEDANCE ANGLE IN DEG | 79.00 MINIMUM AND 85.00 MAXIMUM |
| ZSO IMPEDANCE MAGNITUDE IN OHMS | 1590.00 MINIMUM AND 2050.00 MAXIMUM |
| TERMINAL LOCATION | REAR |
| TERMINAL TYPE AND QUANTITY | 6 SCREW |
| TEST DATA DOCUMENT | 81349-MIL-S-20708 SPECIFICATION (INCLUDES ENGINEERING TYPE BULLETINS, BROCHURES,ETC., THAT REFLECT SPECIFICATION TYPE DATA IN SPECIFICATION FORMAT; EXCLUDES COMMERCIAL CATALOGS, INDUSTRY DIRECTORIES, AND SIMILAR TRADE PUBLICATIONS, REFLECTING GENERAL TYPE DATA ON CERTAIN ENVIRONMENTAL AND PERFORMANCE REQUIREMENTS AND TEST CONDITIONS THAT ARE SHOWN AS "TYPICAL", "AVERAGE", "NOMINAL", ETC.). |
| TRANSFORMATION RATIO | 1.154 ROTOR TO STATOR NOMINAL |
| UNDERCUT DIAMETER | 0.9750 INCHES NOMINAL |
| UNDERCUT WIDTH | 0.0620 INCHES NOMINAL |